Expert Answers about Gulf Stream
- Troubleshooting No Power To 7-Way Trailer Socket On A 2010 Gulf Stream Voyager MH
- It could be a number of reasons why you are not getting power to your 7-way on your 2010 Gulf Stream Voyager motorhome.
The most most common cause is an insufficient or bad ground. But before you go digging around your wires, I recommend you first quickly check if a fuse has blown.
A blown fuse would also cause your 7-way to not function as the fuse blowing has restricted power to flow to that area.
If the fuse is blown, simply replace the fuse and check again for functionality.
If...
view full answer... - How to Fix Motorhomes Hyperflashing after Installing LED Taillights
- Your motorhome must have a bulb out sensor. Becasue LED's draw so much less power than incandescents, the bulb-out sensor thinks the bulb is out and causes the circuit to hyperflash. You'll need to install a load resistor like # ALEDRST2B on each lamp. The resistor would plug inline between your existing PL3 plug and the lamp for a plug and play installation. This assumes you're using the # STL23RB lamp you referenced. If you're using a different lamp, you'd use the # DI34ZR and wire it...
view full answer... - Antennae Repair on Drive Wireless RV Backup Camera System
- To repair antennae wire on your Drive Wireless RV Backup Camera System, # 324-000002, please note the attached images. Depending on the type of damage, these connectors are threaded and can be disassembled. If damage is at the end of the wire, I suggest unthreading the components, removing damaged portion, cutting it away and reconnecting the fittings. Unfortunately we do not have a repair faculty for this to be sent to. If what I listed above does help resolve your issue, or the remaining...
view full answer... - Fan And Lid Does Not Operate On MaxxFan 4751KS Roof Vent
- I recommend verifying if the fan is getting 12v to the motor when the button is pushed. You can use # PT29ZR to verify if you're receiving 12 volts.
If you're not receiving 12v, then you likely have a bad motor, which you can replace it with # MA10-20270.
If you're receiving 12v to your motor, I suggest next checking your operator mechanism. You'll need to head to the roof, open the cover manually, and visually inspect for damage.
If it's broken, you can use the Replacement Operator...
view full answer... - Troubleshooting Flashing Lights on Curt Spectrum Trailer Brake Controller
- According to the instructions for the Curt Spectrum Trailer Brake Controller # C51170 there are 2 reasons why the lights should be flashing.
The first is if it's flashing red and yellow which means the brake controller is overloaded or there is a short-circuit somewhere on the brake controller line. To remedy this you'll need to check your wiring and connections and fix the short.
The second is if it's flashing blue and this indicates that the trailer has been disconnected or if the brakes...
view full answer... - Troubleshooting Hazard Lights Not Working on Trailer Towed By RV
- By discovering that the trailer's hazard lights work perfectly when hooked up to your truck, you have at least narrowed down the problem area to the motorhome and know the wiring on the trailer is good.
The first thing I recommend doing is taking a circuit tester like # PTW2979 and testing each of the pins on the RV's 7-Way while you have the corresponding light function activated. I have attached a 7-Way wiring diagram to assist. If the brake/turn or running light circuit isn't getting...
view full answer... - Troubleshooting Drive Stereo CD/DVD Mechanism
- Try doing a hard reset to your Drive RV Stereo, # 324-000148 by unplugging the wiring harness for a minimum of 15 minutes until the circuit board resets itself. Also check to ensure there isn't any debris or excessive dust build up inside the disc opening. You can use the canned compress air, what is used to clean keyboards and PC's, to blow out the inside.
view full answer... - Troubleshooting Tail Light Issues On A 2007 Gulf Stream Conquest Travel Trailer
- I would start determining if the problem is on the trailer or the tow vehicle side of the wiring. You will need to use a circuit tester like our part # PTW2993 to test the functions of the trailer wiring harness on your tow vehicle. A video is included to show how this is done. While your testing the running light pin on your tow vehicle make sure the connector is clean and free of corrosion. Do the same for the trailer's connector.
If the problem is on the tow vehicle then most likely...
view full answer...
Go To Results